• New Keypad Button Modes: You can now configure individual keypad buttons for non-toggle scene control, allowing a button to send On only or Off only instead of alternating between On and Off. To change a button's behavior, open the keypad's Device Details page and select Button Modes. Note: Keypad backlight behavior may not always reflect the expected button state if the button is also controlled by other scenes. • Motion Sensor 3 Support: Added support for the upcoming release of the new Insteon Motion Sensor 3.

• Fix issues with devices unexpectedly displaying a "Limited Support" message

• Fixed an issue where new scenes didn't display after being created

• App will now remember which room view you were on last • Fix scene controls on the virtual Mini Remote view • Fix issues with "Unsupported Device" sometimes showing unexpectedly • Fix issues with editing/creating alerts • Fix an issue where there could be a crash during logout • General performance improvements

• Scene builder improvements - when adding a controller-only device to an existing scene, Director will not re-write other controller-only scene members • Motion sensor onboarding fixes and improvements • Removed DST toggle in favor of exclusively location-based time and date settings for Insteon Hubs • General crash fixes

• Fix an issue where IO modules added to scenes may change from latching to momentary switch mode in some cases • UI and performance improvements

• Fix for schedules not being deleted when a device is deleted from the app. • Remove scene error alert if not able to show affected devices. • Remove in-app sensor alerts if the data is stale. • Various crash fixes.

• Fixed an issue where the IO Module might not be fully configured during onboarding. If you previously saw this, use Restore Device in the IO Module’s details. • Resolved freezes when editing local device properties. • Fixed errors when adjusting sunrise/sunset offsets. • Addressed a few app crashes to improve overall stability.

Thank you for using Insteon! • Fixes renaming issues and crashes in scene builder • Other performance improvements

• Fix a rare crash on launch issue • Update temperature and other value pickers that would sometimes show blank text • Resolve an issue where the app could crash switching to a house with no rooms

• Performance improvements and updates to make the app launch faster • Improved room assignment workflow when adding a new device • Fixed a rare issue where house health update would successfully complete, but indicate failure

Introducing Home Health Tools: Fix common issues related to device configurations in the hub, unexpected schedules, and more. You can find it under Settings > Home Health Tools.

• Refreshed Insteon look for a cleaner, more modern experience • Faster device status updates • Fixed minor issues with email and push notification settings

• Resolved an issue with our ceiling fan controller status not updating as expected

• Fixed an issue related to alert messages for dual outlets

• Fixes onboarding issue for the Insteon Siren which is now available on insteon.com

• Fixed an issue related to sensor status displaying offline in some circumstances • Added an easier way to link Insteon to your Amazon Alexa directly from Director (Settings > Integrations) • Added support for legacy Insteon Heat Pump Thermostat (Model #2732-242) • Added more information to the delete device process

• Director now ensures the most accurate device state upon launching the app. • You can also initiate a whole house status update by pulling down on any room screen.

• Fixed an issue with keypads in the scene builder • Fixed an issue with adding devices as responders in a scene

Fixed crashes related to IO Module and Insteon Thermostat control

• Fix an issue where some devices LED indicators were not being configured as expected • Fix an issue that could cause hub setup to become stuck

• You can now restore a device that has been factory reset or has otherwise lost links back to the hub. Director will automatically detect these missing links when you attempt to control a device. Or you can visit the Device Details page for a device and select Restore Device. Both options will ensure all hub links and scene links are in place and will ensure optimal status reporting. • Improved responsiveness when you open the app and quickly try controlling a device. • Fixed an issue with deleting contacts when editing alerts • Fixed issue with led indicator state sometimes being incorrect

• Fixed an issue with setting On Level for dimmable device. • Fixed indicator light for plug-in devices to show enable/disable.

• Fixed an issue where adding a scene to favorites didn’t save. • Fixed an issue where the app continued to display a deleted battery powered device. • Fixed inconsistencies in the UI for adjusting certain device properties. • We now display more types of sensors during the onboarding process. • Added the ability to create a new room from the Device Details > Rooms page. • You can now properly turn off the indicator lights on your i3 Keypad.

• Fixed issues with setting Motion Sensor 2 properties. • Fixed issues with setting LED indicator brightness. • Fixed issue that was allowing a device to be director over multiple scenes. • General UI improvements. • Accessibility updates to navigation.